-
-
Save boozeman/d7c5499fdc59ba0cf7b1fa9e42b7f534 to your computer and use it in GitHub Desktop.
| esphome: | |
| name: nedis-esp-004 | |
| substitutions: | |
| device_name: nedis_esp_004 | |
| friendly_name: Nedis ESP 004 | |
| # Nedis WIFIPO121FWT with bk7231N | |
| # Nedis WIFIPO120FWT with bk7231N chip has markings "10T40 and µ" on it's label | |
| # Nedis WIFIPO120FWT with bk7231T chip has no those markings on it's label | |
| # Create HA input Helper (example 0-7200 seconds) with device friendly_name for pulsetime Function | |
| # DISCLAIMER: The Rear Lights Warranty is on. Use at your own risk! | |
| bk72xx: | |
| board: generic-bk7231n-qfn32-tuya | |
| logger: | |
| web_server: | |
| captive_portal: | |
| ota: | |
| password: !secret ota_password | |
| mdns: | |
| api: | |
| encryption: | |
| key: "Generate API-key: https://esphome.io/components/api.html?highlight=randomly%20generated" | |
| wifi: | |
| ssid: !secret wifi_ssid | |
| password: !secret wifi_password | |
| ap: | |
| ssid: "${friendly_name} Fallback Hotspot" | |
| password: !secret ap_password | |
| text_sensor: | |
| - platform: libretiny | |
| version: | |
| name: ${device_name} LibreTiny Version | |
| binary_sensor: | |
| - platform: gpio | |
| id: ${device_name}_binary_switch_1 | |
| pin: | |
| number: P7 | |
| inverted: false | |
| mode: INPUT_PULLUP | |
| on_press: | |
| then: | |
| - switch.toggle: ${device_name}_switch_1 | |
| switch: | |
| - platform: gpio | |
| id: ${device_name}_switch_1 | |
| name: ${friendly_name} Relay 1 | |
| pin: P8 | |
| on_turn_on: | |
| - light.turn_on: ${device_name}_red_light_status | |
| - script.execute: pulsetime # Initialize pulsetime script | |
| on_turn_off: | |
| - light.turn_off: ${device_name}_red_light_status | |
| - script.stop: pulsetime # Initialize pulsetime script | |
| light: | |
| - platform: status_led | |
| id: ${device_name}_blue_light_status | |
| pin: | |
| number: P10 | |
| inverted: false | |
| - platform: status_led | |
| id: ${device_name}_red_light_status | |
| pin: | |
| number: P6 | |
| inverted: false | |
| sensor: | |
| - platform: hlw8012 | |
| model: BL0937 | |
| cf_pin: | |
| number: P26 | |
| inverted: true | |
| cf1_pin: | |
| number: P24 | |
| inverted: true | |
| sel_pin: | |
| number: P11 | |
| inverted: true | |
| current: | |
| name: ${friendly_name} Current | |
| id: ${device_name}_current | |
| voltage: | |
| name: ${friendly_name} Voltage | |
| id: ${device_name}_voltage | |
| filters: | |
| # Map from sensor -> measured value | |
| - calibrate_linear: | |
| - 0.0 -> 0.0 | |
| - 579.0 -> 235.7 | |
| power: | |
| name: ${friendly_name} Power | |
| id: ${device_name}_power | |
| filters: | |
| - calibrate_linear: | |
| - 0.0 -> 0.0 | |
| - 717.11688 -> 265.8 | |
| energy: | |
| name: ${friendly_name} Energy | |
| id: ${device_name}_energy | |
| voltage_divider: 1881 # 4 * 470K resistors upstream and 1k resistor downstream for voltage divider (4 x 470 000 + 1000) / 1000 | |
| current_resistor: 0.001 ohm | |
| update_interval: 60s | |
| # Example configuration entry with 2 sensors and filter | |
| - platform: wifi_signal # Reports the WiFi signal strength/RSSI in dB | |
| name: "${friendly_name} WiFi Signal dB" | |
| id: ${device_name}_wifi_signal_db | |
| update_interval: 60s | |
| entity_category: "diagnostic" | |
| # Input helper as sensor for pulsetime script | |
| - platform: homeassistant | |
| name: "${friendly_name} Pulsetime" | |
| id: ${device_name}_pulsetime | |
| entity_id: input_number.${device_name}_pulsetime #The entity of input_number in HA | |
| # Tasmota like pulsetime script | |
| script: | |
| - id: pulsetime | |
| then: | |
| - if: | |
| condition: | |
| lambda: 'return id(${device_name}_pulsetime).state > 0;' | |
| then: | |
| - delay: !lambda |- | |
| return id(${device_name}_pulsetime).state * 1000; | |
| - switch.turn_off: ${device_name}_switch_1 |
Could this be modified so blue led indicates online and the red one indicates switch on/off?
Hi,
I tried this but No success. I have to check this out again. I have not opened this model. Previous model do not have any gpio:s for another Led.
Found it on P6 after looking at https://www.elektroda.com/rtvforum/topic3926632.html
Made a fork and updated it there https://gist.github.com/ChristianRonningen/ee6ec5941bb2212473c793b548d7d47d
Thanks for making this, i would not have been able to do create this yaml config :)
Found it on P6 after looking at https://www.elektroda.com/rtvforum/topic3926632.html Made a fork and updated it there https://gist.github.com/ChristianRonningen/ee6ec5941bb2212473c793b548d7d47d Thanks for making this, i would not have been able to do create this yaml config :)
Hi,
I'm glad if this was useful. I will implement your modifications to my conf. I Just added missing power filters to my confs here.
Remember to calibrate the voltage and current values of your socket. I personally use a cheap power consumption meter for this, and a vegetable dehydrator serves as the load.
Yes, noticed that after getting readings of 550volt.
Used a cheap "kill-a-watt" and this https://esphome.io/components/sensor/hlw8012.html#hlw8012-power-sensor wedsite, so if anyone find this in the future then know where to look for help on that too :)
Could this be modified so blue led indicates online and the red one indicates switch on/off?