-
-
Save cameroncondry/12435bd50eae451c2247ab1d86675873 to your computer and use it in GitHub Desktop.
| ; Optimized start routine: Provides a single drop-in script | |
| ; for an optimized startup routine. Faster, safer, & easier | |
| ;===== machine: A1 Mini =================================== | |
| ;===== date: 20251111 ===================================== | |
| ;===== version: 1.3.4 ===================================== | |
| ;===== modified by: Cascade Media LLC ===================== | |
| ;===== changelog: ========================================= | |
| ;===== 1.3.4 - Disabled vibration compensation due to eddy sensor warnings | |
| ;===== 1.3.3 - Enabled quick vibration compensation | |
| ;===== 1.3.2 - Disabled vibration compensation | |
| ; - Shows signs of underextrusion when enabled | |
| ;===== 1.3.1 - Adds quick version of vibration compensation | |
| ;===== 1.3 - Adds 0.2mm and 0.6mm nozzle support | |
| ; - Enhances nozzle temperature handling | |
| ; - Updates guarded movements for safety | |
| ; - Adds mech-mode (vibration) optional check | |
| ; - Improved accuracy on stabilization pattern | |
| ;===== 1.2 - Optimized all paths | |
| ;===== 1.1 - Release for public | |
| ;===== 1.0 - Initial version | |
| ;===== start warm-up sequence ============================= | |
| M1002 gcode_claim_action : 2 ; status: heating | |
| M1002 set_filament_type:{filament_type[initial_no_support_extruder]} | |
| ; conservative nozzle preheat based on material | |
| M104 S{nozzle_temperature_initial_layer[initial_extruder] - 50} | |
| M140 S{bed_temperature_initial_layer_single} | |
| G392 S0 ; disable clog detect | |
| M9833.2 ; bambu: set noise/mech params | |
| ;===== start printer sound ================================ | |
| ; remove sounds for quieter startup | |
| ;castle-complete | |
| ;music_long: 5.837832 | |
| M17 | |
| M400 S1 | |
| M1006 S1 | |
| M1006 L84 M70 N99 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A0 B8 C25 D8 M35 E49 F8 N31 | |
| M1006 A37 B8 L64 C25 D8 M35 E44 F8 N38 | |
| M1006 A0 B8 C25 D8 M35 E44 F8 N38 | |
| M1006 A32 B8 L42 C25 D9 M35 E41 F9 N38 | |
| M1006 A0 B8 C25 D8 M35 E41 F7 N38 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A0 B8 C25 D8 M35 E49 F8 N31 | |
| M1006 A37 B8 L64 C25 D8 M35 E44 F8 N38 | |
| M1006 A0 B8 C25 D8 M35 E44 F8 N38 | |
| M1006 A32 B8 L42 C25 D8 M35 E41 F8 N38 | |
| M1006 A0 B8 C25 D8 M35 E41 F8 N38 | |
| M1006 A41 B24 L68 C25 D24 M35 E49 F25 N31 | |
| ;Tick 122, Time 1 sec | |
| M73 P17 R0 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A0 B8 C0 D8 E49 F8 N31 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A0 B8 C0 D8 E49 F8 N31 | |
| M1006 A41 B8 L68 C25 D8 M35 E49 F8 N31 | |
| M1006 A0 B9 C0 D9 E49 F8 N31 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| ;Tick 203, Time 2 sec | |
| M73 P34 R0 | |
| M1006 A0 B8 C26 D8 M28 E50 F8 N52 | |
| M1006 A38 B8 L61 C26 D8 M28 E45 F8 N45 | |
| M1006 A0 B8 C26 D8 M28 E45 F8 N45 | |
| M1006 A33 B8 L56 C26 D8 M28 E42 F8 N38 | |
| M1006 A0 B8 C26 D8 M28 E42 F8 N38 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| M1006 A0 B8 C26 D8 M28 E50 F8 N52 | |
| M1006 A38 B8 L61 C26 D9 M28 E45 F9 N45 | |
| M1006 A0 B8 C26 D8 M28 E45 F7 N45 | |
| M1006 A33 B8 L56 C26 D8 M28 E42 F8 N38 | |
| M1006 A0 B8 C26 D8 M28 E42 F8 N38 | |
| M1006 A42 B24 L79 C26 D24 M28 E50 F24 N52 | |
| ;Tick 316, Time 3 sec | |
| M73 P51 R0 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F9 N52 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| M1006 A0 B8 C0 D8 E50 F8 N52 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| M1006 A0 B8 C0 D8 E50 F8 N52 | |
| M1006 A42 B8 L79 C26 D8 M28 E50 F8 N52 | |
| M1006 A0 B8 C0 D8 E50 F8 N52 | |
| M1006 A44 B8 L83 C35 D8 M59 E52 F8 N69 | |
| M1006 A0 B8 C0 D8 E52 F8 N69 | |
| ;Tick 405, Time 4 sec | |
| M73 P68 R0 | |
| M1006 A40 B8 L71 C32 D8 M45 E47 F9 N45 | |
| M1006 A0 B8 C0 D8 E47 F7 N45 | |
| M1006 A35 B8 L50 C28 D8 M21 E44 F8 N38 | |
| M1006 A0 B8 C0 D8 E44 F8 N38 | |
| M1006 A44 B8 L83 C35 D8 M59 E52 F8 N69 | |
| M1006 A0 B8 C0 D8 E52 F8 N69 | |
| M1006 A40 B8 L71 C32 D8 M45 E47 F8 N45 | |
| M1006 A0 B8 C0 D8 E47 F8 N45 | |
| M1006 A35 B8 L50 C28 D8 M21 E44 F8 N38 | |
| M1006 A0 B8 C0 D8 E44 F8 N38 | |
| M1006 A44 B24 L83 C35 D24 M59 E52 F24 N69 | |
| ;Tick 511, Time 5 sec | |
| M73 P85 R0 | |
| M1006 A44 B8 L83 C35 D8 M59 E52 F8 N69 | |
| M1006 A44 B8 L83 C35 D8 M59 E52 F8 N69 | |
| M1006 A44 B8 L83 C35 D8 M59 E52 F8 N69 | |
| M1006 A46 B8 L83 C37 D8 M69 E54 F8 N69 | |
| M1006 A0 B8 C0 D8 E0 F8 | |
| M1006 A46 B8 L83 C37 D8 M69 E54 F8 N69 | |
| M1006 A0 B9 C0 D9 E0 F9 | |
| M1006 A46 B8 L83 C37 D8 M69 E54 F8 N69 | |
| M1006 A0 B8 C0 D8 E0 F8 | |
| M1006 A48 B97 L83 C39 D97 M69 E56 F97 N49 | |
| M1006 W | |
| M18 | |
| ;===== initialize machine status ========================== | |
| G90 ; absolute positioning | |
| M83 ; relative extrusion | |
| M211 X1 Y1 Z1 ; enable soft endstops | |
| M630 S0 P0 ; bambu: reset internal state | |
| M204 S6000 ; set default acceleration | |
| M17 X0.7 Y0.9 Z0.5 ; set motor current | |
| M960 S5 P1 ; enable toolhead lamp | |
| M220 S100 ; feedrate to 100% | |
| M221 S100 ; flowrate to 100% | |
| M982.2 S1 ; enable cog noise reduction | |
| M975 S1 ; enable motion gating | |
| M106 P1 S0 ; disable fan while heating | |
| M73.2 R1.0 ; bambu: reset time left magnitude | |
| ;===== home and stage printer ============================= | |
| M17 ; enable motors | |
| G28 X Y ; safely home X and Y | |
| G0 X55 Y175 F10000 ; move to safe place to home Z | |
| G380 S2 Z5 F1200 ; guarded clearance before homing | |
| G28 Z P0 T300 ; safely home Z | |
| M400 ; wait for movements | |
| M211 S ; push endstop status | |
| M211 X0 Y0 Z0 ; disable soft endstop | |
| G1 Z5 F2000 ; add clearance before move | |
| G1 X0 F10000 ; move to service area | |
| G1 X-13.5 F3000 ; move into wiper | |
| M400 | |
| ;===== switch material in AMS ============================= | |
| M620 M ; enable remap | |
| M620 S[initial_no_support_extruder]A | |
| G392 S1 ; enable clog detect | |
| M1002 gcode_claim_action : 4 | |
| M400 | |
| M1002 set_filament_type:UNKNOWN | |
| M109 S[nozzle_temperature_initial_layer] | |
| M104 S250 | |
| M400 | |
| T[initial_no_support_extruder] | |
| G1 X-13.5 F3000 | |
| M400 | |
| M620.1 E F{filament_max_volumetric_speed[initial_no_support_extruder]/2.4053*60} T{nozzle_temperature_range_high[initial_no_support_extruder]} | |
| M109 S250 ; set nozzle to common flush temp | |
| M106 P1 S0 | |
| G92 E0 | |
| G1 E50 F200 | |
| M400 | |
| M1002 set_filament_type:{filament_type[initial_no_support_extruder]} | |
| M104 S{nozzle_temperature_range_high[initial_no_support_extruder]} | |
| G92 E0 | |
| G1 E50 F{filament_max_volumetric_speed[initial_no_support_extruder]/2.4053*60} | |
| M400 | |
| M106 P1 S178 | |
| G92 E0 | |
| G1 E5 F{filament_max_volumetric_speed[initial_no_support_extruder]/2.4053*60} | |
| M109 S{nozzle_temperature_initial_layer[initial_no_support_extruder]-20} | |
| M104 S{nozzle_temperature_initial_layer[initial_no_support_extruder]-40} | |
| G92 E0 | |
| G1 E-0.5 F300 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F12000 | |
| G1 X-13.5 F3000 | |
| ; reset nozzle to expected temperature | |
| M104 S{nozzle_temperature_initial_layer[initial_no_support_extruder] - 50} | |
| G392 S0 ; disable clog detect | |
| M621 S[initial_no_support_extruder]A | |
| ;===== build plate detection (flagged) ==================== | |
| M1002 judge_flag build_plate_detect_flag | |
| M622 S1 | |
| G39.4 ; bambu: quick build plate detection | |
| M400 | |
| ; quick mech-mode resonance check for improving vertical artifacts | |
| ; runs ONLY when "Bed Leveling" is enabled | |
| ; uses vibration amplitude to work on all nozzles | |
| ; @warning: reliably triggers the eddy current sensor warning, testing alternatives to the long and loud sweeps from the default routine | |
| ; G1 X128 Y128 Z10 F20000 ; use bed center for symetrical testing | |
| ; M400 P200 | |
| ; M970.3 Q1 A7 B30 C80 H12 K0 O2 | |
| ; M974 Q1 S2 P0 | |
| M623 | |
| ;===== clean nozzle ======================================= | |
| M1002 gcode_claim_action : 14 ; status: nozzle cleaning | |
| G90 | |
| M83 | |
| M106 P1 S255 ; short blast to neck any strands | |
| G4 P800 | |
| M106 P1 S0 ; keep fan off during heating | |
| ; perform a short knock sequence by bending | |
| ; oozed filament before brushing sequence | |
| G1 E-1.0 F500 ; small retract before taps | |
| G1 Z5 F2000 ; clearance | |
| G0 X90 Y-4 F10000 ; move to the purge area | |
| G380 S3 Z-2 F1200 ; gentle tap on plate | |
| G1 Z2 F2000 | |
| G1 X91 F3000 | |
| G380 S3 Z-2 F1200 | |
| G1 Z2 F2000 | |
| G1 X92 F3000 | |
| G380 S3 Z-2 F1200 | |
| ; brush material on rubber | |
| G1 Z5 F2000 | |
| G1 X25 Y176 F20000 | |
| G1 Z0.2 F2000 | |
| G1 Y186 | |
| G91 | |
| G1 X-30 F20000 | |
| G1 Y-2 | |
| G1 X27 | |
| G1 Y1.5 | |
| G1 X-28 | |
| G1 Y-2 | |
| G1 X30 | |
| G1 Y1.5 | |
| G1 X-30 | |
| G90 | |
| G1 Z5 F2000 | |
| ; brush material on rubber, slight offset | |
| G1 Z5 F2000 | |
| G1 X25 Y177 F20000 | |
| G1 Z0.2 F2000 | |
| G1 Y187 | |
| G91 | |
| G1 X-30 F20000 | |
| G1 Y-2 | |
| G1 X27 | |
| G1 Y1.5 | |
| G1 X-28 | |
| G1 Y-2 | |
| G1 X30 | |
| G1 Y1.5 | |
| G1 X-30 | |
| G90 | |
| G1 Z5 F2000 | |
| ; restore protections and establish raw Z reference | |
| M211 R ; restore softend status | |
| G29.2 S0 ; disable ABL for raw Z | |
| G0 X55 Y175 F10000 | |
| G28 Z P0 T300 | |
| G29.2 S1 ; enable ABL | |
| ;===== park and wait for heating ========================== | |
| M1002 gcode_claim_action : 2 ; status: heating | |
| G1 Z5 F2000 ; ensure clearance | |
| G1 X10 Y10 F10000 ; park clear of brush | |
| ; set and wait for bed to final temperature | |
| M140 S[bed_temperature_initial_layer_single] | |
| M104 S{nozzle_temperature_initial_layer[initial_extruder] - 50} | |
| M190 S[bed_temperature_initial_layer_single] | |
| ;===== bed leveling (flagged) ============================= | |
| M1002 judge_flag g29_before_print_flag | |
| M622 J1 | |
| G29.2 S0 ; disable ABL for probing | |
| M1002 gcode_claim_action : 1 ; status: auto bed leveling | |
| G29 A1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} I{first_layer_print_size[0]} J{first_layer_print_size[1]} | |
| M400 | |
| M500 ; save mesh | |
| G29.2 S1 ; enable ABL with fresh mesh | |
| M623 | |
| ;===== bed leveling (not flagged) ========================= | |
| M1002 judge_flag g29_before_print_flag | |
| M622 J0 | |
| M1002 gcode_claim_action : 13 ; status: homing toolhead | |
| G28 T300 ; permissive temp home | |
| G29.2 S1 ; enable ABL with existing mesh | |
| M623 | |
| ;===== nozzle load line =================================== | |
| M1002 gcode_claim_action : 2 ; status: heating | |
| M975 S1 ; enable motion gating (explicit) | |
| G90 ; re-assert positioning (explicit) | |
| M83 | |
| T1000 ; select local tool | |
| M211 S ; push endstop status | |
| M211 X0 Y0 Z0 ; disable soft endstop | |
| G1 Z5 F2000 ; add clearance before move | |
| G1 X0 F10000 ; move to service area | |
| G1 X-13.5 F3000 ; move into wiper | |
| ; minimal prime with micro-retract inside service area | |
| G92 E0 ; reset extruded amount before line | |
| G1 E1.2 F500 | |
| G1 E-0.25 F1500 | |
| ; set and wait for nozzle to final temperature | |
| M104 S{nozzle_temperature_initial_layer[initial_extruder]} | |
| M109 S{nozzle_temperature_initial_layer[initial_extruder]} | |
| ;===== prepare sensors for calibration ==================== | |
| M1002 set_filament_type:UNKNOWN ; prepare filament for calibration | |
| M412 S1 ; enable filament runout detect | |
| M400 | |
| M620.3 W1 ; enable filament tangle detect | |
| G392 S0 ; disable clog detect during calibration | |
| M400 S2 P100 ; small wait with sensor settle | |
| ;===== flow dynamics calibration (flagged) ================ | |
| M1002 set_filament_type:{filament_type[initial_no_support_extruder]} | |
| M1002 judge_flag extrude_cali_flag | |
| M622 J1 | |
| M1002 gcode_claim_action : 8 ; status: calibrating extrusion | |
| M900 K0.0 L1000.0 M1.0 ; pressure advance baseline | |
| G90 | |
| M83 ; re-assert positioning (explicit) | |
| G1 Z5 F2000 ; safe lift | |
| G0 X68 Y-4 F10000 ; move near start position | |
| G0 Z0.3 F2000 ; move to start position | |
| M400 | |
| G0 X88 E10 F{outer_wall_volumetric_speed/(24/20)*60} | |
| G0 X93 E.3742 F{outer_wall_volumetric_speed/(0.3*0.5)/4*60} | |
| G0 X98 E.3742 F{outer_wall_volumetric_speed/(0.3*0.5)*60} | |
| G0 X103 E.3742 F{outer_wall_volumetric_speed/(0.3*0.5)/4*60} | |
| G0 X108 E.3742 F{outer_wall_volumetric_speed/(0.3*0.5)*60} | |
| G0 X113 E.3742 F{outer_wall_volumetric_speed/(0.3*0.5)/4*60} | |
| G0 Y0 Z0 F20000 ; finish the patterned sweep | |
| M400 | |
| G1 X-13.5 Y0 Z10 F10000 ; park in service area | |
| M400 | |
| ; primary dynamic extrusion compensation | |
| G1 E10 F{outer_wall_volumetric_speed/2.4*60} | |
| M983 F{outer_wall_volumetric_speed/2.4} A0.3 H[nozzle_diameter] | |
| M106 P1 S180 ; enable fan to neck strand | |
| M400 S7 ; short settle | |
| G1 X0 F20000 ; wipe & shake | |
| G1 X-13.5 F3000 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F12000 | |
| G1 X-13.5 F3000 | |
| M400 | |
| M106 P1 S0 ; disable fan | |
| ; retry once if needed | |
| M1002 judge_last_extrude_cali_success | |
| M622 J0 | |
| M983 F{outer_wall_volumetric_speed/2.4} A0.3 H[nozzle_diameter] | |
| M106 P1 S180 | |
| M400 S7 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F12000 | |
| G1 X-13.5 F3000 | |
| M400 | |
| M106 P1 S0 | |
| M623 | |
| ; final corrections and cleanup | |
| G1 X-13.5 F3000 | |
| M400 | |
| M984 A0.1 E1 S1 F{outer_wall_volumetric_speed/2.4} H[nozzle_diameter] | |
| M106 P1 S180 | |
| M400 S7 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F12000 | |
| G1 X-13.5 F3000 | |
| M400 | |
| M106 P1 S0 | |
| M623 ; end flow dynamics calibration | |
| M211 R ; restore soft endstops status | |
| ;===== extrude calibration test =========================== | |
| ; hold first-layer temp and set modes (explicit) | |
| M109 S{nozzle_temperature_initial_layer[initial_extruder]} | |
| M190 S{bed_temperature_initial_layer_single} | |
| G90 | |
| M83 | |
| ; clear any ooze before calibrating | |
| M106 P1 S180 ; moderate fan for PLA and PETG | |
| M400 S2 | |
| G1 E-0.05 F1500 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F20000 | |
| G1 X-13.5 F3000 | |
| G1 X0 F12000 | |
| G1 X-13.5 F3000 | |
| M106 P1 S0 | |
| M400 | |
| ; draw short stabilization pattern | |
| G1 Z5 F3000 | |
| G0 X68 Y-2.5 F20000 | |
| G0 Z0.3 F3000 | |
| G0 X88 E10 F{outer_wall_volumetric_speed/(24/20)*60} | |
| G0 X93 E0.3742 F{outer_wall_volumetric_speed/(0.3*0.5)/4*60} | |
| G0 X98 E0.3742 F{outer_wall_volumetric_speed/(0.3*0.5)*60} | |
| G0 X103 E0.3742 F{outer_wall_volumetric_speed/(0.3*0.5)/4*60} | |
| G0 X108 E0.3742 F{outer_wall_volumetric_speed/(0.3*0.5)*60} | |
| G0 X113 E0.3742 F{outer_wall_volumetric_speed/(0.3*0.5)/4*60} | |
| G0 X115 Z0 F20000 | |
| G1 Z5 F3000 | |
| M400 | |
| ;===== for textured pei plate ============================= | |
| {if curr_bed_type=="Textured PEI Plate"} | |
| G29.1 Z{-0.02} | |
| {endif} | |
| ;===== normalize lights/fans & re-enable protections ===== | |
| M960 S1 P0 ; light/laser ch1 off | |
| M960 S2 P0 ; light/laser ch2 off | |
| M960 S5 P0 ; toolhead lamp off | |
| M106 P1 S0 ; part fan off | |
| M106 P2 S0 ; aux fan off | |
| M106 P3 S0 ; chamber fan off | |
| G392 S1 ; re-enable clog detect | |
| G29.2 S1 ; enable ABL for print | |
| ;===== final staging ===================================== | |
| M1002 gcode_claim_action : 0 ; status: printing | |
| M975 S1 ; keep vibration suppression on | |
| G90 | |
| M83 | |
| T1000 | |
| M211 R ; restore endstop status | |
| M211 X0 Y0 Z0 ; disable soft endstops | |
| M1007 S1 ; bambu: keep enabled | |
| ; ===== hand-off to slicer first move ===================== |
Hi, when using your gcode HMS reports "The sensitivity of Y-axis eddy current sensor is too low." Any idea why this happens?. When going back to stock gcode there is no error.
I have the same issue. I thought my A1mini needed cleaning, but it did not solve it. After researching I think the problem may be this line :
M970.3 Q1 A7 B30 C80 H12 K0 O2. ; v1.3.3
M970.3 Q1 A7 K0 O2 ; Bambu version
Explanation
The values B30 C80 H12 suggest a frequency sweep from 30-80 Hz with 12 measurement points. This is reasonably aggressive and requires good sensor readings. If your plate isn't perfectly seated or the sensors are slightly dirty, this test will fail.
Will try modifying this line with the original Tomorrow and report back.
I tested with the Bambu original line, and the error persists.
Hi, I like your g-code.
In section "Build plate detection", on line 203 you write: Runs ONLY when "Bed Leveling" is enabled
Do you mean "Bed Detection" or the resonance test should be in the "Bed Leveling" section?
@maniq2 Is your version ready for general use, or are you still testing ?
My version is without AMS and sound. I have done many prints with it without default. There is still an error message on the printer, same for the version with AMS and sound.
Ahh I see, I have starred your gist. Will use when error gets fixed. Thanks for the update though .. i also want to use without AMS and sound.
EDIT: Cant find your fork now.
@tanishqmanuja @maniq2 @Otto-luke I'm getting the same warning, and it is definitely part of the fast vibration check. The default checks are longer and louder, but they cover a lot more bands. I'm going to update the script to remove the quick check for now until I can test it more with the various bands. Thanks again for the reports!
@tanishqmanuja @maniq2 @Otto-luke The vibration check has been disabled in the latest 1.3.4 version. Run the built-in maintenance mode calibration to reset the warning before running a print. Sorry that I didn't catch the issue sooner!
I've started using two different startup sounds to differentiate 0.2 and 0.4mm nozzles. This has been suprisingly helpful in avoiding accidently using the wrong printer profiles. If you're a millenial, I use the version in this gist for 0.4mm and this for 0.2mm nozzles (replace lines 35-120 in the gist):
;John Williams - Hedwig's Theme (Harry Potter OST)
;music_long: 11.727261
M17
M400 S1
M1006 S1
M1006 L70 M70 N99
M1006 E48 F27 N31
M1006 E53 F40 N69
M1006 E56 F13 N49
M1006 E0 F1
M1006 E55 F27 N69
;Tick 109, Time 1 sec
M73 P8 R0
M1006 E53 F45 N69
M1006 E0 F9
M1006 E60 F26 N69
M1006 E60 F1 N69
M1006 E58 F73 N61
;Tick 264, Time 2 sec
M73 P17 R0
M1006 E0 F9
M1006 E55 F72 N69
;Tick 345, Time 3 sec
M73 P25 R0
M1006 E55 F1 N69
M1006 E53 F40 N69
M1006 E56 F13 N49
;Tick 409, Time 4 sec
M73 P34 R0
M1006 E55 F27 N69
M1006 E52 F45 N69
M1006 E0 F9
M1006 E54 F27 N69
;Tick 518, Time 5 sec
M73 P42 R0
M1006 E48 F127 N31
;Tick 645, Time 6 sec
M73 P51 R0
M1006 E0 F10
M1006 E48 F26 N31
M1006 E48 F1 N31
M1006 E53 F40 N69
;Tick 722, Time 7 sec
M73 P59 R0
M1006 E0 F1
M1006 E56 F13 N49
M1006 E55 F27 N69
M1006 E0 F1
M1006 E53 F45 N69
;Tick 809, Time 8 sec
M73 P68 R0
M1006 E0 F9
M1006 E60 F27 N69
M1006 E63 F45 N69
M1006 E0 F9
;Tick 900, Time 9 sec
M73 P76 R0
M1006 E62 F27 N69
M1006 E61 F45 N69
M1006 E0 F9
M1006 E57 F27 N56
;Tick 1009, Time 10 sec
M73 P85 R0
M1006 E61 F40 N69
M1006 E0 F1
M1006 E60 F13 N69
M1006 E0 F1
M1006 E59 F26 N69
M1006 E59 F1 N69
M1006 E47 F45 N45
;Tick 1136, Time 11 sec
M73 P93 R0
M1006 E0 F9
M1006 E56 F27 N49
M1006 E0 F1
M1006 E53 F127 N69
M1006 W
M18
Only difference is the sound played or something else also, I am HP fan, I want the sound for my 0.4mm 😅
v1.3.4 disables the vibration check that is triggering the Y-axis warning. If you still have the eddy current warning after auto calibration, try power cycling the printer.
I'm testing out some alternatives for the vibration testing, because the benefits to VFAs are nice. I wish I could add a toggle in the interface that allows you to toggle full vibration calibration, like we do with bed leveling and flow dynamics.
Hi, when using your gcode HMS reports "The sensitivity of Y-axis eddy current sensor is too low." Any idea why this happens?. When going back to stock gcode there is no error.