U-Boot SPL 2013.07 (Sep 14 2023 - 13:47:16)
Board info: T41NQ
apll_freq = 1008000000
mpll_freq = 1200000000
vpll_freq = 1188000000
sdram init start
DDR clk rate 600000000
DDRP_INNOPHY_PLL_CTRL: 00000028
DDRP_INNOPHY_PLL_CTRL: 00000020
T41NQ ddr phy skew set
CPU0 RESET ERROR PC: 5e7e9ff8
CPU1 RESET ERROR PC: befe3bfa
mem data:
81000000: 00000000 ffffffff 00000000 ffffffff
81000010: 00000000 ffffffff 00000000 ffffffff
81000020: 00000000 ffffffff 00000000 ffffffff
81000030: 00000000 ffffffff 00000000 ffffffff
spl_sfc_nand_load:412
00006c00,00064000,80100000
spl_sfc_nand_load:415
image entry point: 0x80100000
Board: ISVP (Ingenic XBurst2 T41 SoC)
DRAM size is 128 MiB
Top of RAM usable for U-Boot at: 88000000
Reserving 464k for U-Boot at: 87f88000
Reserving 32896k for malloc() at: 85f68000
Reserving 32 Bytes for Board Info at: 85f67fe0
Reserving 124 Bytes for Global Data at: 85f67f64
Reserving 128k for boot params() at: 85f47f64
Stack Pointer at: 85f47f48
Now running in RAM - U-Boot at: 87f88000
NAND: 0 MiB
SFC_NAND: ***sfc init!
MMC: MSC: 0
NAND read: device 0 offset 0xc0000, size 0x20000
131072 bytes read: OK
NAND read: device 0 offset 0xe0000, size 0x20000
131072 bytes read: OK
Data transfer: serial
Net: Jz4775-9161
Hit any key to stop autoboot: 0
Nand Init Done!
BootConcifg: Magic[0xCBAE9527] Boot MTD[kernel:1 rootfs:2 appfs:3]
do_mmc_init start!
do_mmc_init device not found!
NAND read: device 0 offset 0x100000, size 0x300000
3145728 bytes read: OK
Image Name: Linux-4.4.94
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2246517 Bytes = 2.1 MiB
Load Address: 80010000
Entry Point: 80499910
Verifying Checksum ... OK
Uncompressing lzma Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.4.94 (root@cp3) (gcc version 7.2.0 (Ingenic Linux-Release5.1.4.1-Default(xburst2(fp64)+glibc2.29+Go language) 2022.08-08 10:51:21) ) #1 SMP PREEMPT Thu Sep 14 13:54:09 CST 2023
[ 0.000000] CPU0 RESET ERROR PC:5E7E9FF8
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00132100 (Ingenic XBurst@II)
[ 0.000000] FPU revision is: 00f32100
[ 0.000000] MIPS: machine is ingenic,marmot
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 00629000 @ 00010000 (usable)
[ 0.000000] memory: 00037000 @ 00639000 (usable after init)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 03800000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x00000000037fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x00000000037fffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000037fffff]
[ 0.000000] [SMP] Slave CPU(s) 1 available.
[ 0.000000] Primary instruction cache 32kB, VIPT, 8-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Unified secondary cache 128kB 8-way, linesize 64 bytes.
[ 0.000000] PERCPU: Embedded 10 pages/cpu @81097000 s8528 r8192 d24240 u40960
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 14224
[ 0.000000] Kernel command line: console=ttyS1,115200n8 mem=56M@0x0 rmem=38M@0x3800000 nmem=34M@0x5E00000 init=/linuxrc ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs ro system=/dev/mtdblock3 mtdparts=sfc0_nand:1M(uboot),3M(kernel),8M(rootfs),32M(appfs),3M(kernel2),8M(rootfs2),32M(appfs2),41728k(param),128k(SN),-(bootconfig) lpj=11968512
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 49852K/57344K available (4672K kernel code, 271K rwdata, 1356K rodata, 220K init, 156K bss, 7492K reserved, 0K cma-reserved)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] parse cpu-intc-iomap, intc define in dt is too large!
[ 0.000000] core irq setup finished and percpu irq inited! NR_IRQS = 419
[ 0.000000] t41 Clock Power Management Unit init sucess!
[ 0.000000] parse cpu-ost-iomap, ost number define in dt is too large!
[ 0.000000] percpu cpu_num:0 timerevent init
[ 0.000000] clockevents_config_and_register success.
[ 0.000000] clocksource: jz_clocksource: mask: 0x7fffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000000] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000452] Console: colour dummy device 80x25
[ 0.004895] Calibrating delay loop (skipped) preset value.. 2393.70 BogoMIPS (lpj=11968512)
[ 0.013355] pid_max: default: 32768 minimum: 301
[ 0.018240] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.024875] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.032665] [SMP] Prepare 2 cores., cpu: 0
[ 0.116007] [SMP] Booting CPU1 ...
[ 0.119380] CPU1 RESET ERROR PC:FFFE0FC4
[ 0.119397] Primary instruction cache 32kB, VIPT, 8-way, linesize 32 bytes.
[ 0.119401] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[ 0.119406] Unified secondary cache 128kB 8-way, linesize 64 bytes.
[ 0.119472] percpu cpu_num:1 timerevent init
[ 0.119490] clockevents_config_and_register success.
[ 0.119495] CPU1 revision is: 00132100 (Ingenic XBurst@II)
[ 0.119498] FPU revision is: 00f32100
[ 0.119743] Brought up 2 CPUs
[ 0.166584] devtmpfs: initialized
[ 0.174702] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.184696] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.190991] pinctrl core: initialized pinctrl subsystem
[ 0.196716] NET: Registered protocol family 16
[ 0.206419] ingenic pinctrl 10010000.pinctrl: 4 gpio chip add success, pins 128
[ 0.214452] ingenic pinctrl 10010000.pinctrl: ingenic pinctrl probe success
[ 0.227536] dmmu_init 807 PTRS_PER_PTE = 1024
[ 0.303728] ingenic-dma 13420000.dma: INGENIC SoC DMA initialized
[ 0.311003] inno phy probe success
[ 0.317351] clocksource: Switched to clocksource jz_clocksource
[ 0.344272] NET: Registered protocol family 2
[ 0.349194] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.356197] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.362726] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.369272] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.375134] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.381749] NET: Registered protocol family 1
[ 0.386448] RPC: Registered named UNIX socket transport module.
[ 0.392459] RPC: Registered udp transport module.
[ 0.397150] RPC: Registered tcp transport module.
[ 0.401972] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.411231] squashfs: version 4.0 (2021/14/49) Phillip Lougher
[ 0.417666] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.431561] jitterentropy: Initialization failed with host not compliant with requirements: 2
[ 0.440782] io scheduler noop registered
[ 0.444688] io scheduler deadline registered
[ 0.449086] io scheduler cfq registered (default)
[ 0.453975] ingenic,t41-pwm 13460000.pwm: PWM clk100k:480
[ 0.459425] ingenic,t41-pwm 13460000.pwm: period_ns:max=1365312,min=42
[ 0.468558] Ingenic drawbox probe sucess!
[ 0.472921] vpu_register
[ 0.475408] helix probe success
[ 0.480697] aip_init success
[ 0.484116] 10031000.serial: ttyS1 at MMIO 0x10031000 (irq = 58, base_baud = 6250000) is a uart1
[ 0.493053] console [ttyS1] enabled
[ 0.493053] console [ttyS1] enabled
[ 0.500195] bootconsole [early0] disabled
[ 0.500195] bootconsole [early0] disabled
[ 0.509062] 10035000.serial: ttyS5 at MMIO 0x10035000 (irq = 64, base_baud = 6250000) is a uart5
[ 0.523512] ingenic-tcu 10002000.tcu: Ingenic TCU driver register completed ret = 0
[ 0.532672] ingenic-sfc 13440000.sfc0: Found Supported nand device, id = 0xc891,name = GD5F1GM7UE
[ 0.542018] use nand common get feature interface!
[ 0.547075] Scanning device for bad blocks
[ 0.555360] random: nonblocking pool is initialized
[ 0.656234] ingenic-sfc 13440000.sfc0: NOTICE: this flash haven`t param, magic_num:3040506
[ 0.664936] ingenic-sfc 13440000.sfc0: read partition from flash failed!
[ 0.671978] ingenic-sfc 13440000.sfc0: read mtdparts!
[ 0.677295] 10 cmdlinepart partitions found on MTD device sfc0_nand
[ 0.683883] Creating 10 MTD partitions on "sfc0_nand":
[ 0.689284] 0x000000000000-0x000000100000 : "uboot"
[ 0.696069] 0x000000100000-0x000000400000 : "kernel"
[ 0.702920] 0x000000400000-0x000000c00000 : "rootfs"
[ 0.709791] 0x000000c00000-0x000002c00000 : "appfs"
[ 0.716505] 0x000002c00000-0x000002f00000 : "kernel2"
[ 0.723508] 0x000002f00000-0x000003700000 : "rootfs2"
[ 0.730482] 0x000003700000-0x000005700000 : "appfs2"
[ 0.737321] 0x000005700000-0x000007fc0000 : "param"
[ 0.744130] 0x000007fc0000-0x000007fe0000 : "SN"
[ 0.750673] 0x000007fe0000-0x000008000000 : "bootconfig"
[ 0.757918] ingenic-sfc 13440000.sfc0: SPI NAND MTD LOAD OK
[ 0.764162] dwc2 13500000.otg: Configuration mismatch. Forcing peripheral mode
[ 0.771886] OTG CLK 1f877fc4
[ 0.776293] CPCCR CLK 1580
[ 0.779180] dwc2 13500000.otg: 1024 invalid for host_nperio_tx_fifo_size. Check HW configuration.
[ 0.788527] dwc2 13500000.otg: 1024 invalid for host_perio_tx_fifo_size. Check HW configuration.
[ 0.837386] dwc2 13500000.otg: EPs: 9, dedicated fifos, 3576 entries in SPRAM
[ 0.846075] ingenic-i2c 10050000.i2c: register i2c0 success.
[ 0.853788] Netfilter messages via NETLINK v0.30.
[ 0.858886] ip_set: protocol 6
[ 0.862261] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.867995] NET: Registered protocol family 17
[ 0.875177] soc_vpu probe success,version:1.0.0-03203fd46d
[ 0.881666] ubi0: attaching mtd2
[ 0.917182] ubi0: scanning is finished
[ 0.931627] ubi0: attached mtd2 (name "rootfs", size 8 MiB)
[ 0.937511] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 0.944722] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 0.951862] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 0.959183] ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
[ 0.965390] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 0.972990] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1613115762
[ 0.982594] ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 20
[ 0.992325] ubi0: background thread "ubi_bgt0d" started, PID 440
[ 1.795633] UBIFS (ubi0:0): static UBI volume - read-only mode
[ 1.906383] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
[ 1.915127] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.925553] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1142785 bytes (1 MiB, 8 LEBs)
[ 1.936147] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[ 1.942275] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 66570D54-F10D-4066-9340-BA62BB90C300, small LPT model
[ 1.954876] UBIFS (ubi0:0): full atime support is enabled.
[ 1.960715] VFS: Mounted root (ubifs filesystem) readonly on device 0:14.
[ 1.968619] devtmpfs: mounted
[ 1.971885] Freeing unused kernel memory: 220K
mdev is ok......
net.core.wmem_max = 26214400
net.core.wmem_default = 26214400
[ 2.293281] ubi1: attaching mtd3
[ 2.426105] ubi1: scanning is finished
[ 2.440719] ubi1: attached mtd3 (name "appfs", size 32 MiB)
[ 2.446623] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.455697] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.462892] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.470250] ubi1: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
[ 2.476548] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 2.484189] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 213084148
[ 2.493716] ubi1: available PEBs: 0, total reserved PEBs: 256, PEBs reserved for bad PEB handling: 20
[ 2.503436] ubi1: background thread "ubi_bgt1d" started, PID 463
UBI device number 1, total 256 LEBs (32505856 bytes, 31.0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 2.618141] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "appfs", R/O mode
[ 2.626728] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.637180] UBIFS (ubi1:0): FS size: 27172864 bytes (25 MiB, 214 LEBs), journal size 3936256 bytes (3 MiB, 31 LEBs)
[ 2.648142] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB)
[ 2.654264] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 76A3E9B4-4FC5-40A8-A713-C60D6EA75E8A, small LPT model
[ 2.666968] UBIFS (ubi1:0): full atime support is enabled.
[ 2.687192] ubi2: attaching mtd7
Ingenic-uc1_1 login: [ 2.856013] ubi2: scanning is finished
[ 2.869912] ubi2 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 18, need 20
[ 2.881733] ubi2: attached mtd7 (name "param", size 40 MiB)
[ 2.889516] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.896733] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.903926] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.911275] ubi2: good PEBs: 326, bad PEBs: 0, corrupted PEBs: 0
[ 2.917634] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 2.925210] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 486846354
[ 2.934744] ubi2: available PEBs: 0, total reserved PEBs: 326, PEBs reserved for bad PEB handling: 18
[ 2.944457] ubi2: background thread "ubi_bgt2d" started, PID 473
UBI device number 2, total 326 LEBs (41394176 bytes, 39.4 MiB), available 0 LEBs (0 bytes), LEB [ 2.956995] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 476
size 126976 bytes (124.0 KiB)
[ 3.017751] UBIFS (ubi2:0): recovery needed
[ 3.086870] UBIFS (ubi2:0): recovery completed
[ 3.091668] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "param"
[ 3.099375] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 3.109795] UBIFS (ubi2:0): FS size: 36061184 bytes (34 MiB, 284 LEBs), journal size 4952064 bytes (4 MiB, 39 LEBs)
[ 3.120761] UBIFS (ubi2:0): reserved for root: 0 bytes (0 KiB)
[ 3.126881] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 23029520-4356-4915-BF48-E1DC463D5845, small LPT model
[ 3.139075] UBIFS (ubi2:0): full atime support is enabled.
[ 3.908005] sdhci: Secure Digital Host Controller Interface driver
[ 3.914539] sdhci: Copyright(c) Pierre Ossman
[ 3.977392] mmc0: SDHCI controller on ingenic-sdhci [13060000.msc] using ADMA
[ 3.987552] mmc0: card removed
[ 4.027400] mmc1: SDHCI controller on ingenic-sdhci [13070000.msc] using ADMA
[ 4.160239] mmc1: new high speed SDIO card at address 0001
[ 4.200513] [atbm_log]:SVN_VER=22688,DPLL_CLOCK=24,BUILD_TIME=[===== =====]
[ 4.207904] [atbm_log]:----drvier RATEPOLCIY=OLD
[ 4.212940] [atbm_log]:Probe called
[ 4.216679] [atbm_log]:atbm_sdio_probe:v12
[ 4.221051] [atbm_log]:Allocated hw_priv @ 8063af00
[ 4.226837] [atbm_log]:[BH] register.
[ 4.230852] [atbm_log]: wait_event_interruptible from send_prbresp_wq
[ 4.237845] [atbm_log]:atbmwifi INIT_WORK enable
[ 4.242834] [atbm_log]:atbmwifi INIT_WORK enable
[ 4.247839] [atbm_log]:atbm_before_load_firmware++
[ 4.252912] [atbm_log]:atbm_sdio_rx_thread
[ 4.258042] [atbm_log]:atbm_HwGetChipType, chipver=0x49, g_wifi_chip_type[10]
[ 4.265812] [atbm_log]:atbm_before_load_firmware:0xab0016c = [34800000]
[ 4.273160] [atbm_log]:atbm_before_load_firmware:0xab0016c = [34800000]
[ 4.280140] [atbm_log]:rx timeout
[ 4.283993] [atbm_log]:atbm_before_load_firmware:do not set config to smu
[ 4.529840] [atbm_log]:atbm_before_load_firmware:read [0x16100074]=[0],ret(0)
[ 4.537519] [atbm_log]:atbm_before_load_firmware:write [0x16100074]=[1],ret(0)
[ 4.783280] [atbm_log]:atbm_start_load_firmware++
[ 4.788258] [atbm_log]:used firmware.h=
[ 4.792300] [atbm_log]:START DOWNLOAD ICCM=========
[ 4.797442] [atbm_log]:atbm_load_firmware_generic: addr 10000: len 22000
[ 4.881622] [atbm_log]:START DOWNLOAD DCCM=========
[ 4.886748] [atbm_log]:atbm_load_firmware_generic: addr 800000: len 9000
[ 4.913918] [atbm_log]:atbm_after_load_firmware++
[ 4.946682] [atbm_log]:firmwareCap f589
[ 4.950733] [atbm_log]:firmwareCap2 5984
[ 4.954844] [atbm_log]:wsm_caps.firmwareCap 5984f589
[ 4.959892] [atbm_log]:apollo wifi WSM init done.
[ 4.959892] Input buffers: 42 x 1728 bytes
[ 4.959892] Hardware: 7.1280
[ 4.959892] WSM firmware [=MODEM=RF=Ares_AX 2GHZ Dec 9 2022 16:08:35NOTXConfrim ap sleep], ver: 15425, build: 2980, api: 1060, cap: 0x5984F589 Config[30004] expection 900b80c, ep0 cmd addr 901d3f8 NumOfStations[4] NumOfInterfaces[3]
[ 4.995035] [atbm_log]:EFUSE(8) [0]
[ 4.995058] [atbm_log]:atbm_after_load_firmware:1380==> val32 = 4001200
[ 4.995141] [atbm_log]:set_block_size=256
[ 4.995146] [atbm_log]:mdelay wait wsm_startup_done !!
[ 4.995261] [atbm_log]:atbm_sdio_tx_thread
[ 5.020025] [atbm_log]:EFUSE(I) [1]
[ 5.024044] [atbm_log]:EFUSE(B) [0]
[ 5.027895] [atbm_log]:CAPABILITIES_ATBM_PRIVATE_IE [0]
[ 5.033828] [atbm_log]:CAPABILITIES_NVR_IPC [0]
[ 5.039778] [atbm_log]:CAPABILITIES_NO_CONFIRM [1]
[ 5.045711] [atbm_log]:CAPABILITIES_SDIO_PATCH [0]
[ 5.051656] [atbm_log]:CAPABILITIES_NO_BACKOFF [0]
[ 5.057601] [atbm_log]:CAPABILITIES_CFO [0]
[ 5.063533] [atbm_log]:CAPABILITIES_AGC [1]
[ 5.069477] [atbm_log]:CAPABILITIES_TXCAL [1]
[ 5.075410] [atbm_log]:CAPABILITIES_MONITOR [0]
[ 5.081364] [atbm_log]:CAPABILITIES_CUSTOM [1]
[ 5.087297] [atbm_log]:CAPABILITIES_SMARTCONFIG [0]
[ 5.093249] [atbm_log]:CAPABILITIES_ETF [1]
[ 5.099193] [atbm_log]:CAPABILITIES_LMAC_RATECTL [1]
[ 5.105127] [atbm_log]:CAPABILITIES_LMAC_TPC [1]
[ 5.111069] [atbm_log]:CAPABILITIES_LMAC_TEMPC [1]
[ 5.117001] [atbm_log]:CAPABILITIES_CTS_BUG [0]
[ 5.122947] [atbm_log]:CAPABILITIES_USB_RECOVERY_BUG [0]
[ 5.128891] [atbm_log]:CAPABILITIES_USE_IPC [0]
[ 5.134822] [atbm_log]:CAPABILITIES_OUTER_PA [0]
[ 5.140768] [atbm_log]:CAPABILITIES_POWER_CONSUMPTION [0]
[ 5.146700] [atbm_log]:CAPABILITIES_RSSI_DECIDE_TXPOWER [0]
[ 5.152647] [atbm_log]:CAPABILITIES_RTS_LONG_DURATION [1]
[ 5.158590] [atbm_log]:CAPABILITIES_TX_CFO_PPM_CORRECTION[1]
[ 5.164521] [atbm_log]:CAPABILITIES_SHARE_CRYSTAL [0]
[ 5.170372] [atbm_log]:CAPABILITIES_HW_CHECKSUM [0]
[ 5.176304] [atbm_log]:CAPABILITIES_SINGLE_CHANNEL_MULRX [1]
[ 5.182247] [atbm_log]:CAPABILITIES_CFO_DCXO_CORRECTION [1]
[ 5.188192] [atbm_log]:EX_CAPABILITIES_TWO_CHIP_ONE_SOC [0]
[ 5.193851] [atbm_log]:EX_CAPABILITIES_MANUAL_SET_AC [0][atbm_log]:EX_CAPABILITIES_LMAC_BW_CONTROL [1]
[ 5.203721] [atbm_log]:EX_CAPABILITIES_SUPPORT_TWO_ANTENNA [0][atbm_log]:EX_CAPABILITIES_ENABLE_STA_REMAIN_ON_CHANNEL [0]
[ 5.215237] [atbm_log]:EX_CAPABILITIES_ENABLE_PS [1][atbm_log]:EX_CAPABILITIES_TX_REQUEST_FIFO_LINK [0]
[ 5.225836] [atbm_log]:EX_CAPABILITIES_CHIP_TYPE 6032IS
[ 5.231599] [atbm_log]:CONFIG_PRODUCT_TEST_USE_FEATURE_ID [1]
[ 5.237634] [atbm_log]:CONFIG_PRODUCT_TEST_USE_GOLDEN_LED [1]
[ 5.244307] [atbm_log]:wsm_generic_confirm:status(2)
[ 5.249610] [atbm_log]:<WARNING> wsm_write_mib fail !!! mibId=4132
[ 5.256594] [atbm_log]:apollo wifi : can't open /data/.mac.info
[ 5.263305] [atbm_log]:efuse data is [0x1,0x28,0x1b,0x1b,0x1d,0xf,0x0,0x0,0x38:0xbe:0xab:0xe:0x92:0x81]
[ 5.273234] [atbm_log]:apollo wifi : can't open /tmp/atbm_txpwer_dcxo_cfg.txt
[ 5.280778] [atbm_log]:apollo wifi : can't open /tmp/set_rate_power.txt
[ 5.288040] [atbm_log]:get chip id [a4][1][1]
[ 5.292708] [atbm_log]:current chiptype 6031s
[ 5.297637] [atbm_log]:cfg80211_regdomain is NULL
[ 5.302630] [atbm_log]:country code 00 country_support_chan = 14
[ 5.309496] [atbm_log]:enable sg
[ 5.314577] [atbm_log]:enable sg
[ 5.319676] [atbm_log]:is registered as 'ALTOBEAM'
[ 5.324748] [atbm_log]:[atbm_wtd]:set wtd_probe = 1
[ 5.576948] no manual card detect
[ 5.707627] @@@@ tx-isp-probe ok (version H20221101a) compiler date: Nov 18 2022 @@@@
[ 5.735968] @@@@ avpu driver ok(version H20220825a) @@@@@
[ 5.777549] @@@@@ inner codec power up@@@@@@
[ 6.197443] @@@@ audio driver ok(version H20210526a) @@@@@
[ 6.226280] @@@@@ multi-process system driver init @@@@@
[ 6.232290] nmem_size = 34M
[ 6.235225] nmem_start = 0x5E00000
[ 6.248594] soc_nna_probe success
[ 6.252235] soc_nna_init success
Normal Boot---->
wait wlan0 up
watch_cache run interval 10 sec
wlan0 init done
[ 6.277668] watch_cache (577): drop_caches: 3
Successfully initialized wpa_supplicant
wpa_suplicant deamon finish
wdt_init success
version: 1.1.22
GIT 87115e237b50dc8169598e4d2dfbd8db9376f9e4 2023-08-31T17:33:38+08:00
Query_MTD[FlashTool.c:124]:BlockSize 131072
DiskMgrServices[DiskMgr.c:102]:DiskMgrServices Starting....
DRIVERS-version T41..
[ 7.074027] soc_nna_open: open sucess
[ 7.082902] soc-nna version is 00000041
The soc-nna version is 00000041
[I/magik::venus]: ***********************
[I/magik::venus]: venus memory map size: 0
[I/magik::venus]: ***********************
@@ Ingenic AIP LIB Ver is H20230705a @@
[I/magik::venus]: ***********************
[I/magik::venus]: venus init sucess.
[I/magik::venus]: ***********************
INFO(magik): venus version:0.2.0.2.ALPHA(00000200_f19c0fa) built:20230814-2317(7.2.0 r5.1.8 libc2.29 mips T41@NNA2)
INFO(magik): model version:0.1.9.NNA2_9b46aad
INFO(magik): model version:0.1.0.NNA2_5232523
INFO(magik): model version:0.1.0.NNA2_5232523
IMP_Plat_Init[jz/t41/IMP_Platform.c:99]:chris aVersion:IMP-1.0.1
IMP_Check_Sensor[jz/t41/IMP_Platform.c:81]:Sensor[sc4336p, I2C_ADDR:0x30]
[ 8.975726] ==>0 client = 81821e00 sensor=82b81c00
[ 8.985437] set sensor mclk(0) gpio
[ 8.989210]
[ 8.989210] ====>[default_boot=0] [resolution=2560x1440] [video_interface=0] [MCLK=0]
[ 9.097523] -----sc4336p_detect: 547 ret = 0, v = 0x9c
[ 9.103064] -----sc4336p_detect: 555 ret = 0, v = 0x42
[ 9.108479] sc4336p chip found @ 0x30 (i2c0)
[ 9.112958] sensor driver version H20230531a
[ 9.117838] Create framechan0 OK!
[ 9.121800] Create framechan1 OK!
[ 9.125766] Create framechan2 OK!
[ 9.617488] sc4336p stream on
---- FPGA board is ready ----
Board UID : 30AB6E51
Board HW ID : 71000260
Board rev. : 62D42E77
Board date : 20211214
-----------------------------
IMP_Plat_Init[jz/t41/IMP_Platform.c:209]:IMP System init Done!
FontMatrix_Load[AVCodec.c:168]:FontMatrixPath[/system/res/iso8859-1-24x48.bin]
FontMatrix_SizeCheck[AVCodec.c:153]:Font Path[/system/res/iso8859-1-24x48.bin] width[24] height[48]
FontMatrix_Load[AVCodec.c:168]:FontMatrixPath[/system/res/iso8859-1-16x32.bin]
FontMatrix_SizeCheck[AVCodec.c:153]:Font Path[/system/res/iso8859-1-16x32.bin] width[16] height[32]
Pipeline_Init[AVCodec.c:250]:==>chnn[0] isEnable[1]
IMP_Plat_VIPP_Enable[jz/t41/IMP_Platform.c:329]:-->CH0 width[2560] height[1440] fps[15]
IMP_Plat_OSD_Enable[jz/t41/IMP_Platform.c:2193]:Channle0 create Rgn0 handle[0] off[1964x20] res[576x48]
IMP_Plat_OSD_Enable[jz/t41/IMP_Platform.c:2193]:Channle0 create Rgn1 handle[1] off[100x1300] res[360x116]
Pipeline_Init[AVCodec.c:250]:==>chnn[1] isEnable[1]
IMP_Plat_VIPP_Enable[jz/t41/IMP_Platform.c:329]:-->CH1 width[1024] height[576] fps[15]
IMP_Plat_ALGO_Enalbe[jz/t41/IMP_Platform.c:2408]:IMP_IVS_CreateChn channle[1] success!
IMP_Plat_OSD_Enable[jz/t41/IMP_Platform.c:2193]:Channle1 create Rgn0 handle[2] off[620x20] res[384x32]
IMP_Plat_OSD_Enable[jz/t41/IMP_Platform.c:2193]:Channle1 create Rgn1 handle[3] off[50x510] res[160x52]
[WARNING]: The specified ScalingList is not allowed; it will be adjusted
Pipeline_Init[AVCodec.c:250]:==>chnn[2] isEnable[1]
[WARNING]: Ignoring GOP params, value will be adjusted
Pipeline_Init[AVCodec.c:250]:==>chnn[3] isEnable[1]
IMP_Plat_AENC_Enable[jz/t41/IMP_Platform.c:1566]:IMP_AENC_CreateChn 0 success!
Pipeline_Init[AVCodec.c:250]:==>chnn[4] isEnable[1]
IMP_Plat_AOPP_Enable[jz/t41/IMP_Platform.c:1763]:=====>Channle4 malloc done[0x14f1790]
warn: shm_init,53shm init already
Module_Init[AVCodec.c:364]:Module init done!
VENC_StartService[Venc.c:614]:CH0 will start video encode service! runMode[0] viDev[0] veChn[0]
VENC_StartService[Venc.c:617]:CH0 working thread creatting!
IMP_Plat_VIN_StartCapture[jz/t41/IMP_Platform.c:970]:Channel[0] IMP_FrameSource_EnableChn[0] done!
IMP_Plat_VENC_StartCapture[jz/t41/IMP_Platform.c:710]:IMP_Encoder_StartRecvPic for channel[0]!
VENC_StartService[Venc.c:614]:CH1 will start video encode service! runMode[0] viDev[0] veChn[1]
VENC_StartService[Venc.c:617]:CH1 working thread creatting!
IMP_Plat_VIN_StartCapture[jz/t41/IMP_Platform.c:970]:Channel[1] IMP_FrameSource_EnableChn[1] done!
IMP_Plat_VIN_StartCapture[jz/t41/IMP_Platform.c:981]:CH1 IMP_FrameSource_SetFrameDepth viChn[1] depth[1] done!
IMP_Plat_VENC_StartCapture[jz/t41/IMP_Platform.c:710]:IMP_Encoder_StartRecvPic for channel[1]!
VENC_StartService[Venc.c:614]:CH2 will start video encode service! runMode[0] viDev[1] veChn[2]
IMP_Plat_VENC_StartCapture[jz/t41/IMP_Platform.c:710]:IMP_Encoder_StartRecvPic for channel[2]!
warn: shm_init,53shm init already
PipelineWorker[Venc.c:491]:Event->result[0x1505f90]
VENC_OsdResource_Init[Venc.c:160]:Channle1 rgn1 isEnable[1] isShow[1]
VENC_OsdResource_Init[Venc.c:160]:Channle1 rgn2 isEnable[0] isShow[0]
VENC_OsdResource_Init[Venc.c:160]:Channle1 rgn3 isEnable[0] isShow[0]
IMP_Plat_ALGO_StartService[jz/t41/IMP_Platform.c:2503]:IMP_IVS_StartRecvPic channle[1]
VENC_CustomOSD_Refresh[Venc.c:177]:Channle[1] index[1] data[0x1364888]
VENC_OsdResource_Init[Venc.c:160]:Channle0 rgn1 isEnable[1] isShow[1]
VENC_OsdResource_Init[Venc.c:160]:Channle0 rgn2 isEnable[0] isShow[0]
VENC_OsdResource_Init[Venc.c:160]:Channle0 rgn3 isEnable[0] isShow[0]
VENC_CustomOSD_Refresh[Venc.c:177]:Channle[0] index[1] data[0x133bc00]
IMP_Plat_AENC_GetOneFrame[jz/t41/IMP_Platform.c:1654]:AENC==>malloc for dummy
aec version: v2.1.201201 in webrtc_profile.ini and v2.1.201201 in aec lib.
PATH:AEC_PATH is empty,normal audio library
IMP_Plat_AIPP_SetAEC[jz/t41/IMP_Platform.c:1484]:IMP_Plat_AIPP_SetAEC done
IMP_Plat_VIN_SetFlip[jz/t41/IMP_Platform.c:1123]:viChn[0] set flip=[0] done!
IMP_Plat_VIN_SetFlip[jz/t41/IMP_Platform.c:1123]:viChn[1] set flip=[0] done!
IMP_Plat_VIN_SetMirror[jz/t41/IMP_Platform.c:1242]:viChn[0] set mirror=[0] done!
IMP_Plat_VIN_SetMirror[jz/t41/IMP_Platform.c:1242]:viChn[1] set mirror=[0] done!
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
curl_easy_perform failed: Error
Ingenic-uc1_1 login: root
Jan 1 00:00:16 login[468]: root login on 'console'
[root@Ingenic-uc1_1:~]# [ 16.299353] watch_cache (577): drop_caches: 3
[root@Ingenic-uc1_1:~]# cat /proc/kcurl_easy_perform failed: Error
[root@Ingenic-uc1_1:~]# cat /proc/jz/
audio/ codecs/ isp/ sinfo/
clock/ dmmu/ reset/ watchdog/
[root@Ingenic-uc1_1:~]# cat /proc/jz/[ 26.325556] watch_cache (577): drop_caches: 3
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-
isp-fs isp-ivdc isp-m0 isp-w00 isp-w01 isp-w02
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-fs
############## framesource 0 ###############
chan status: running
output pixformat:
output resolution: 2560 * 1440
scaler : enable
scaler width: 2560
scaler height: 1440
crop : disable
the state of buffers:
queue count: 2
queue addr: 0x05415900
queue addr: 0x04ecf900
done count: 0
the output buffers is: -2113544064
the losted buffers is: 0
---------------------------
buf:0, state:3, buf_state:30, buf_qcnt:131, buf_dqcnt:130
buf:1, state:3, buf_state:30, buf_qcnt:130, buf_dqcnt:129
############## framesource 1 ###############
chan status: running
output pixformat:
output resolution: 1024 * 576
scaler : enable
scaler width: 1024
scaler height: 576
crop : disable
the state of buffers:
queue count: 2
queue addr: 0x05a33900
queue addr: 0x0595b900
done count: 0
the output buffers is: -2113544064
the losted buffers is: 0
---------------------------
buf:0, state:3, buf_state:30, buf_qcnt:131, buf_dqcnt:130
buf:1, state:3, buf_state:30, buf_qcnt:130, buf_dqcnt:129
############## framesource 2 ###############
chan status: stop
############## framesource 3 ###############
chan status: stop
############## framesource 4 ###############
chan status: stop
############## framesource 5 ###############
chan status: stop
############## framesource 6 ###############
chan status: stop
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-
isp-fs isp-ivdc isp-m0 isp-w00 isp-w01 isp-w02
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-m0
****************** ISP( 0 ) INFO **********************
Software Version : H20221101a
SENSOR NAME : sc4336p
SENSOR OUTPUT WIDTH : 2560
SENSOR OUTPUT HEIGHT : 1440
ISP OUTPUT FPS : 15 / 1
SENSOR OUTPUT : BGGR
SENSOR DFBOOT : 0
ISP Runing Mode : day
Saturation : 128
Sharpness : 128
Contrast : 128
Brightness : 128
Hue : 128
expo fs : 1
Wdr En : 0
Bypass : 0
Antiflicker : disable freq: 0
Antiflicker nodes: 1: step : 0.
*********** Bin Attr ***********
Version : V1.00
DefaultPath :
RunningPath : /etc/sensor/sc4336p-t41.bin
********* Ae Expr Info *********
AeIntegrationTimeUnit : 0
AeMode : 0
AeIntegrationTimeMode : 0
AeAGainManualMode : 0
AeDGainManualMode : 0
AeIspDGainManualMode : 0
AeIntegrationTime : 2990
AeAGain : 1280
AeDGain : 0
AeIspDGain : 1045
AeMinIntegrationTimeMode : 0
AeMinAGainMode : 0
AeMinDgainMode : 0
AeMinIspDGainMode : 0
AeMaxIntegrationTimeMode : 0
AeMaxAGainMode : 0
AeMaxDgainMode : 0
AeMaxIspDGainMode : 1
AeMinIntegrationTime : 2
AeMinAGain : 1024
AeMinDgain : 1024
AeMinIspDGain : 1024
AeMaxIntegrationTime : 2990
AeMaxAGain : 25085
AeMaxDgain : 4096
AeMaxIspDGain : 4096
AeShortMode : 0
AeShortIntegrationTimeMode : 0
AeShortAGainManualMode : 0
AeShortDGainManualMode : 0
AeShortIspDGainManualMode : 0
AeShortIntegrationTime : 0
AeShortAGain : 0
AeShortDGain : 0
AeShortIspDGain : 0
AeShortMinIntegrationTimeMode : 0
AeShortMinAGainMode : 0
AeShortMinDgainMode : 0
AeShortMinIspDGainMode : 0
AeShortMaxIntegrationTimeMode : 0
AeShortMaxAGainMode : 0
AeShortMaxDgainMode : 0
AeShortMaxIspDGainMode : 1
AeShortMinIntegrationTime : 5
AeShortMinAGain : 1024
AeShortMinDgain : 1024
AeShortMinIspDGain : 1024
AeShortMaxIntegrationTime : 94
AeShortMaxAGain : 4096
AeShortMaxDgain : 4096
AeShortMaxIspDGain : 4096
TotalGainDb : 22998
TotalGainDbShort : 0
ExposureValue : 3814
EVLog2 : 779689
debug : 305,0,0,0,0,0,0,0
event debug : 0,0, memopt is 1
static debug :AWB: 329, AE_S: 329, AE_H: 329, AF: 329, GSM: 0
static debug :LCE: 329, ADR: 329, DEFOG: 329, WDR: 0, RMO: 0
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-ivdc
****************** IVDC INFO **********************
IVDC DDR Addr : 0x00000000
IVDC DDR Buffer Size : 0
IVDC DMA Frame Done : 0
IVDC Check Sum Err : 0
IVDC Vpu Err : 0
IVDC ISP Rst : 0
IVDC ISP Frm Err : 0
IVDC Vpu Stop over : 0
IVDC Vpu discard over : 0
IVDC FIFO Overflow : 0
IVDC DDR Overflow : 0
ISP Frame Start : 0
ISP Frame Done : 0
IVDC Y Max ddr line : 0
IVDC UV Max ddr line : 0
help:
clean Max ddr line : set 0x132000ec to 0
,such as:devmem 0x132000ec 32 0x0
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/i[ 36.344199] watch_cache (577): drop_caches: 3
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-
isp-fs isp-ivdc isp-m0 isp-w00 isp-w01 isp-w02
[root@Ingenic-uc1_1:~]# cat /proc/jz/isp/isp-
isp-fs isp-ivdc isp-m0 isp-w00 isp-w01 isp-w02
[root@Ingenic-uc1_1:~]# cat /proc/jz/
audio/ codecs/ isp/ sinfo/
clock/ dmmu/ reset/ watchdog/
[root@Ingenic-uc1_1:~]# cat /proc/jz/
[root@Ingenic-uc1_1:~]#
=========================================================
uboot
U-Boot SPL 2013.07 (Sep 14 2023 - 13:47:16)
Board info: T41NQ
apll_freq = 1008000000
mpll_freq = 1200000000
vpll_freq = 1188000000
sdram init start
DDR clk rate 600000000
DDRP_INNOPHY_PLL_CTRL: 00000028
DDRP_INNOPHY_PLL_CTRL: 00000020
T41NQ ddr phy skew set
CPU0 RESET ERROR PC: 800f061c
CPU1 RESET ERROR PC: 8001c32c
mem data:
81000000: 00000000 ffffffff 00000000 ffffffff
81000010: 00000000 ffffffff 00000000 ffffffff
81000020: 00000000 ffffffff 00000000 ffffffff
81000030: 00000000 ffffffff 00000000 ffffffff
spl_sfc_nand_load:412
00006c00,00064000,80100000
spl_sfc_nand_load:415
image entry point: 0x80100000
Board: ISVP (Ingenic XBurst2 T41 SoC)
DRAM size is 128 MiB
Top of RAM usable for U-Boot at: 88000000
Reserving 464k for U-Boot at: 87f88000
Reserving 32896k for malloc() at: 85f68000
Reserving 32 Bytes for Board Info at: 85f67fe0
Reserving 124 Bytes for Global Data at: 85f67f64
Reserving 128k for boot params() at: 85f47f64
Stack Pointer at: 85f47f48
Now running in RAM - U-Boot at: 87f88000
NAND: 0 MiB
SFC_NAND: ***sfc init!
MMC: MSC: 0
NAND read: device 0 offset 0xc0000, size 0x20000
131072 bytes read: OK
NAND read: device 0 offset 0xe0000, size 0x20000
131072 bytes read: OK
Data transfer: serial
Net: Jz4775-9161
Hit any key to stop autoboot: 0
isvp_t41# <INTERRUPT>
isvp_t41# <INTERRUPT>
isvp_t41# help
? - alias for 'help'
autoboot- Auto check boot config and bootting system
base - print or set address offset
boot - boot default, i.e., run 'bootcmd'
boota - boot android system
bootd - boot default, i.e., run 'bootcmd'
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
echo - echo args to console
env - environment handling commands
ethphy - ethphy contrl
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
gettime - get timer val elapsed,
go - start application at address 'addr'
help - print command description/usage
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
powerinfo- show regulator output voltage and status
printenv- print environment variables
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sfcnand - sfcnand - SFC_NAND sub-system
sleep - delay execution for some time
source - run script from memory
tftpboot- boot image via network using TFTP protocol
version - print monitor, compiler and linker version
watchdog- open or colse the watchdog
isvp_t41#
Created
February 27, 2025 03:38
-
-
Save gtxaspec/82b38223848cb4e1b17e045424827785 to your computer and use it in GitHub Desktop.
wuuk 0910 bootlog
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment