Forked from neoyagami/kipper-ender3-4.2.2-bltouch-g29-g2-g3.cfg
Last active
June 23, 2025 16:41
-
-
Save ExtNeon/bee6862ad71092278e1c6cf10ba91acd to your computer and use it in GitHub Desktop.
Klipper config, ender 3 with 4.2.2 board (the noisy one)
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| CONFIG WAS UPDATED - SEE COMMENTS | |
| DEPRECATED | |
| # This file contains pin mappings for the NON stock 2020 Creality Ender 3 | |
| # with the 32-bit Creality 4.2.2 board. To use this config, during | |
| # "make menuconfig" select the STM32F103 with a "28KiB bootloader" and | |
| # serial (on USART1 PA10/PA9) communication. | |
| # adapted for my printer ender3-4.2.2 with some modifications and without the BLTouch. | |
| # If you prefer a direct serial connection, in "make menuconfig" | |
| # select "Enable extra low-level configuration options" and select | |
| # serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC | |
| # cable used for the LCD module as follows: | |
| # 3: Tx, 4: Rx, 9: GND, 10: VCC | |
| # Flash this firmware by copying "out/klipper.bin" to a SD card and | |
| # turning on the printer with the card inserted. The firmware | |
| # filename must end in ".bin" and must not match the last filename | |
| # that was flashed. | |
| # See docs/Config_Reference.md for a description of parameters. | |
| [stepper_x] | |
| step_pin: PC2 | |
| dir_pin: PB9 | |
| enable_pin: !PC3 | |
| microsteps: 16 | |
| rotation_distance: 40 | |
| endstop_pin: ^PA5 | |
| position_endstop: 0 | |
| position_max: 235 | |
| homing_speed: 50 | |
| [stepper_y] | |
| step_pin: PB8 | |
| dir_pin: PB7 | |
| enable_pin: !PC3 | |
| microsteps: 16 | |
| rotation_distance: 40 | |
| endstop_pin: ^PA6 | |
| position_endstop: 0 | |
| position_max: 235 | |
| homing_speed: 50 | |
| [stepper_z] | |
| step_pin: PB6 | |
| dir_pin: !PB5 | |
| enable_pin: !PC3 | |
| microsteps: 16 | |
| rotation_distance: 8 | |
| endstop_pin: ^PA7 | |
| #endstop_pin: probe:z_virtual_endstop | |
| position_max: 200 | |
| position_min: 0 | |
| [extruder] | |
| max_extrude_only_distance: 100.0 | |
| step_pin: PB4 | |
| dir_pin: PB3 | |
| enable_pin: !PC3 | |
| microsteps: 16 | |
| rotation_distance: 32.000 #That is 100 steps per mm = full_rotation_steps * microsteps / steps_per_mm | |
| nozzle_diameter: 0.400 | |
| filament_diameter: 1.750 | |
| heater_pin: PA1 | |
| sensor_type: EPCOS 100K B57560G104F | |
| sensor_pin: PC5 | |
| control: pid | |
| # tuned for stock hardware with 200 degree Celsius target | |
| pid_Kp: 21.527 | |
| pid_Ki: 1.063 | |
| pid_Kd: 108.982 | |
| min_temp: -30 | |
| max_temp: 250 | |
| pressure_advance: 0.85 | |
| [heater_bed] | |
| heater_pin: PA2 | |
| sensor_type: EPCOS 100K B57560G104F | |
| sensor_pin: PC4 | |
| control: pid | |
| # tuned for stock hardware with 50 degree Celsius target | |
| pid_Kp: 54.027 | |
| pid_Ki: 0.770 | |
| pid_Kd: 948.182 | |
| min_temp: 0 | |
| max_temp: 130 | |
| [fan] | |
| pin: PA0 | |
| [mcu] | |
| serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 | |
| restart_method: command | |
| [board_pins] | |
| aliases: | |
| EXP1_1=PC6,EXP1_3=PB10,EXP1_5=PB14,EXP1_7=PB12,EXP1_9=<GND>, | |
| EXP1_2=PB2,EXP1_4=PB11,EXP1_6=PB13,EXP1_8=PB15,EXP1_10=<5V>, | |
| PROBE_IN=PB0,PROBE_OUT=PB1,FIL_RUNOUT=PC6 | |
| [printer] | |
| kinematics: cartesian | |
| max_velocity: 300 | |
| max_accel: 3000 | |
| max_z_velocity: 5 | |
| max_z_accel: 100 | |
| # Pin mappings for BL_T port | |
| #[bltouch] | |
| #sensor_pin: ^PA7 | |
| #control_pin: PB0 | |
| #z_offset = 0 | |
| #x_offset: -48 | |
| #y_offset: 0 | |
| #[safe_z_home] | |
| #home_xy_position: 165, 130 # Change coordinates to the center of your print bed | |
| #speed: 50 | |
| #z_hop: 10 # Move up 10mm | |
| #z_hop_speed: 5 | |
| #[bed_mesh] | |
| #speed: 150 | |
| #horizontal_move_z: 7 | |
| #mesh_min: 50, 50 | |
| #mesh_max: 180, 200 | |
| #probe_count: 5, 3 | |
| [display] | |
| lcd_type: st7920 | |
| cs_pin: PB12 | |
| sclk_pin: PB13 | |
| sid_pin: PB15 | |
| encoder_pins: ^PB14, ^PB10 | |
| click_pin: ^!PB2 | |
| [gcode_arcs] | |
| resolution = 1.0 | |
| [idle_timeout] | |
| gcode: | |
| DISABLE_STEPPER | |
| TURN_OFF_HEATERS | |
| timeout: 600 | |
| [gcode_macro DISABLE_STEPPER] | |
| gcode: | |
| M84 | |
| [gcode_macro G29] | |
| gcode: | |
| G28 | |
| #BED_MESH_CALIBRATE | |
| G1 X2 Y2 Z5 F4000 | |
| [menu __main __octoprint __poweroff] | |
| type: command | |
| #enable: !toolhead.is_printing | |
| name: Turn off Octopi | |
| gcode: | |
| {action_respond_info('action:poweroff')} |
Author
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Okay folks, here we go: new version of my config file, use with care!
https://gist.github.com/ExtNeon/e582111d5ffd0a44a0e28c425b5d092b